Updated November 2026

Push pull legs muscle groups are sorted by movement pattern rather than by body part. Push days cover the chest, shoulders and triceps, pull days cover the back, rear delts and biceps, and leg days cover the quads, hamstrings, glutes and calves. This guide shows you which muscles belong on each day, how to pick exercises for each one, and how to keep the weekly volume balanced.

Push Day: Chest, Shoulders and Triceps

Push muscles extend the arm or push weight away from the body. The main movers are the pectoralis major, anterior and lateral deltoids, and the triceps. Start with a heavy compound press, then move to accessory work that targets the shoulder and triceps.

Shopping for one? See our guide: Push Pull Legs vs Bro Split (2026): Which Is Better for Building Muscle?.

  • Chest: flat or incline barbell or dumbbell press, 3–4 sets of 6–10 reps
  • Shoulders: seated dumbbell or machine overhead press, 3 sets of 8–12 reps; cable or dumbbell lateral raises, 3 sets of 12–15 reps
  • Triceps: overhead cable extension or skull crusher, 3 sets of 10–15 reps; rope pushdown, 2–3 sets of 12–15 reps

Pull Day: Back, Rear Delts and Biceps

Pull muscles bring weight toward the body. Your lats, rhomboids, traps, rear deltoids and biceps all work here. Because most people already overwork the front of the shoulders, pull days deserve equal or slightly higher volume for the back.

  • Back width: pull-ups or lat pulldowns, 3–4 sets of 6–12 reps
  • Back thickness: chest-supported row or barbell row, 3–4 sets of 8–12 reps
  • Rear delts and upper back: face pulls or reverse pec-deck, 3 sets of 15–20 reps
  • Biceps: incline dumbbell curl and hammer curl, 2–3 sets of 10–15 reps each

Leg Day: Quads, Hamstrings, Glutes and Calves

Leg day is the most demanding session in the split, so schedule it when you have the most energy. It covers the quadriceps, hamstrings, glutes, adductors and calves. Include at least one squat or hinge pattern and one isolation movement for each major muscle group.

  1. Start with a squat variation (back squat, front squat or hack squat): 3–4 sets of 6–10 reps.
  2. Add a hip hinge (Romanian deadlift or leg curl): 3 sets of 8–12 reps.
  3. Use a single-leg movement (split squat or lunge): 2–3 sets of 8–12 reps per leg.
  4. Finish with calf raises and a leg extension or hamstring curl: 2–3 sets of 12–20 reps.

Balancing Weekly Volume Across Muscle Groups

Once each day is set, check that every muscle gets a reasonable weekly set count. Many lifters aim for roughly 10–20 hard sets per muscle group per week, adjusting based on recovery and experience. If your chest appears on push day and also gets indirect work on pull day, you can often run fewer direct chest sets without losing progress.

Muscle group Training day Typical weekly sets
Chest Push 10–16
Shoulders Push (plus indirect pull work) 12–18
Triceps Push 8–12
Back Pull 12–18
Biceps Pull 8–12
Quads, hamstrings, glutes Legs 12–18 each
Calves Legs 8–12

For a full walkthrough of building the schedule around these numbers, see Muscle and Strength Push Pull Legs: A Step-by-Step Guide to Building Your Split.

Common Mistakes

  • Putting all shoulder work on push day and ignoring rear delts on pull day, which can create postural imbalance.
  • Skipping a hip hinge on leg day and relying only on squats, leaving hamstrings and glutes undertrained.
  • Stacking too many isolation sets on top of heavy compounds, which increases fatigue without adding much growth.
  • Adding volume every week without a deload, which tends to stall progress.

If you have an injury or a medical condition, check with a physician or physical therapist before changing your training volume.

FAQ

Which muscles go on push day?

Push day trains the chest, front and side shoulders, and triceps. These muscles all work to extend the arm or press weight away from the body.

Should back get more volume than chest?

Many lifters do well with equal or slightly higher back volume, since most people already train pressing movements heavily. Balancing the two helps shoulder health and posture.

Where do calves fit in a push pull legs split?

Calves belong on leg day, usually as the last exercise. Two or three sets of calf raises per session is a common starting point.

Conclusion

Push pull legs muscle groups are simple to organize once you group movements by pattern: pressing on push day, pulling on pull day, and lower-body work on leg day. Check your weekly set counts so no muscle is neglected, and adjust volume as your recovery changes. Build your plan from there and track your progress over several weeks.

Emily Parker

About Emily Parker

Emily Parker is part of our editorial team and reviews and edits our workout programs & splits guides, checking product details against manufacturer specifications and owner feedback.